Skip to main content
Conation Technologies

Image Analysis Systems

DeXel-Micrometry

Calibrated Dimensional Inspection from a Microscope Image

Check length, diameter, radius, angle, area and profile geometry on a calibrated image. Keep the marked feature, measured value and inspection notes together for review.

Length, Radius and Angle ChecksCalibrated Microscope ImagesTolerance VerificationMarked Inspection Reports
Request Quote

dexel-micrometry-hero.jpg

Recommended source size

1600 × 900 px

Metallurgical microscope connected to a computer displaying DeXel-Micrometry software performing calibrated dimensional measurements on a metallographic specimen with multiple measurement overlays, annotations and engineering drawings.

Process

Calibrate the selected magnification, measure the required feature and retain the marked result in the inspection report.

  1. 01

    Capture the Inspection Image

  2. 02

    Calibrate the Magnification

  3. 03

    Choose the Required Check

  4. 04

    Measure the Feature

  5. 05

    Mark the Result

  6. 06

    Issue the Inspection Report

Measurement Capabilities

Verify visible geometry against the drawing or inspection plan. Every value remains tied to its measurement points and calibrated image.

dexel-micrometry-measurement-tools.jpg

Recommended source size

1440 × 810 px

Software interface displaying multiple calibrated dimensional measurements including line, diameter, radius, angle, area, perimeter, profile, distance, annotations and scale bar over a metallurgical image.

Length

Check widths, heights, depths and straight-line dimensions between selected points.

Diameter

Verify holes, particles and circular features against the specified diameter.

Radius

Check edge radii, fillets and curved profiles where fit or stress concentration matters.

Angle

Verify included angles, tool geometry and feature orientation against the drawing.

Area

Calculate the area inside a traced boundary for particles, pores or sectioned features.

Perimeter

Measure the complete boundary length of an irregular feature or section profile.

Distance Between Features

Check pitch, edge distance, offsets and clearances between visible component features.

Profile Measurement

Trace an irregular edge when a single length or radius cannot describe the geometry.

Annotation

Identify measurement points, acceptance notes and observed defects on the inspection image.

Scale Bar

Add a calibrated reference so reviewers can understand feature size directly from the image.

Software Features

Keep calibration, measurement points, annotations and reported values connected from the first image to the approved inspection record.

Calibration Management

Calibrate each magnification with a certified reference and retain the basis of every dimensional result.

Live Image Capture

Capture the required field directly from a compatible microscope camera before measuring the feature.

Measurement Overlay

Keep dimensions and construction lines visible for review while preserving the original inspection image.

Report Generation

Place measured images, results, specimen identity and inspection notes in a consistent report.

Image Annotation

Mark the exact feature, measurement location and acceptance comment used for the engineering decision.

Data Export

Retain measurement values outside the inspection screen for batch records, comparison and traceability.

Repeatable Inspection Sequence

Use the same capture, calibration, measurement and reporting sequence across operators and production batches.

Upgrade Path

Retain a suitable microscope and camera, or extend the same inspection station when the laboratory also needs metallography, weld or hardness measurement.

dexel-metallography-interface.jpg

Recommended source size

600 × 400 px

DeXel-Metallography

Continue from dimensional checks to calibrated grain, phase, inclusion and microstructure evaluation.

dexel-weld-interface.jpg

Recommended source size

600 × 400 px

DeXel-Weld

Measure weld penetration, throat, leg length and other macro geometry on prepared weld sections.

dexel-hard-interface.jpg

Recommended source size

600 × 400 px

DeXel-Hard

Measure Vickers and Knoop impressions, evaluate hardness traverses and document case depth.

image-analysis-platform.jpg

Recommended source size

600 × 400 px

Image Analysis Systems

Compare DeXel platforms when one laboratory handles dimensional, metallurgical, weld and hardness inspections.

Applications

Use calibrated image measurement when a visible component feature must be checked, compared and documented for an engineering decision.

Incoming and Final Quality Checks
Prepared Specimen Measurement
Tool Edge and Profile Inspection
Component Geometry Verification
Development Sample Comparison
Measurement Method Training
Failure Feature Documentation
Routine Production Verification

Need repeatable dimensional checks from a microscope image?

Share the component feature, drawing tolerance, required accuracy and current microscope. Our application engineers will check the suitable measurement setup.

Request Quote